Engine check
Every test the tile engine is put through, in plain words. They are run again each time the site is published, and a failing test stops the publish.
Every test passed.
Passed
315
Known gaps
6
Failed
0
Last run November 19, 2026 at 7:03 AM, Central time.
What the engine must get right
Where a test is run several ways, such as once for each pattern, the ways are listed under it.
- Covers the surface with no gaps and no overlapsChecked for: stacked, 8'-0" x 8'-0" wall, 4 x 16 tile; stacked, 8'-0" x 8'-0" wall with a window, 4 x 16 tile; stacked, 5'-0" x 8'-0" wall, 3 x 12 tile; stacked, 8'-0" x 5'-0" floor, 12 x 24 tile; brick 1/2, 8'-0" x 8'-0" wall, 4 x 16 tile; brick 1/2, 8'-0" x 8'-0" wall with a window, 4 x 16 tile; brick 1/2, 5'-0" x 8'-0" wall, 3 x 12 tile; brick 1/2, 8'-0" x 5'-0" floor, 12 x 24 tile; brick 1/3, 8'-0" x 8'-0" wall, 4 x 16 tile; brick 1/3, 8'-0" x 8'-0" wall with a window, 4 x 16 tile; brick 1/3, 5'-0" x 8'-0" wall, 3 x 12 tile; brick 1/3, 8'-0" x 5'-0" floor, 12 x 24 tile; herringbone 45, 8'-0" x 8'-0" wall, 4 x 16 tile; herringbone 45, 8'-0" x 8'-0" wall with a window, 4 x 16 tile; herringbone 45, 5'-0" x 8'-0" wall, 3 x 12 tile; herringbone 45, 8'-0" x 5'-0" floor, 12 x 24 tile; herringbone 90, 8'-0" x 8'-0" wall, 4 x 16 tile; herringbone 90, 8'-0" x 8'-0" wall with a window, 4 x 16 tile; herringbone 90, 5'-0" x 8'-0" wall, 3 x 12 tile; herringbone 90, 8'-0" x 5'-0" floor, 12 x 24 tile; diagonal, 8'-0" x 8'-0" wall, 4 x 16 tile; diagonal, 8'-0" x 8'-0" wall with a window, 4 x 16 tile; diagonal, 5'-0" x 8'-0" wall, 3 x 12 tile; diagonal, 8'-0" x 5'-0" floor, 12 x 24 tile; vertical brick 50%, 8'-0" x 8'-0" wall with a window, 4 x 16 tile upright; vertical brick 33%, 8'-0" x 8'-0" wall with a window, 4 x 16 tile upright.Passed
- Tile plus grout accounts for the whole wallChecked for: stacked; brick 1/2; brick 1/3; herringbone 45; herringbone 90; diagonal.Passed
- Cut 1 is the lowest cut and the numbers climbChecked for: stacked; brick 1/2; brick 1/3; herringbone 45; herringbone 90; diagonal; vertical brick.Passed
- Cuts at the same height are numbered left to rightPassed
- A tile is a cut only when it is smaller than a full tile or meets an openingChecked for: stacked; brick 1/2; brick 1/3; herringbone 45; herringbone 90; diagonal.Passed
- A tile fully inside an opening is left outChecked for: stacked; brick 1/2; brick 1/3; herringbone 45; herringbone 90; diagonal.Passed
- Slivers are flagged below the limit and not above itPassed
- The center rule keeps whichever of tile-on-center and joint-on-center leaves the larger end cutsPassed
- With wrap on, the next wall continues the pattern round the cornerPassed
- With wrap off, the next wall starts fresh and is centered on itselfPassed
- A corner does not wrap where the tile or pattern differsPassed
- Sliding a wall by hand moves the walls joined to it by a wrapped cornerPassed
- Full tile at the floorChecked for: the bottom course is a full tile; the bottom tile sits tight to the floor with no joint under it.Passed
- Balance top and bottom: the top and bottom courses match to within one grout jointPassed
- Center on features: the pattern is centered on the windowPassed
- Changing a tile from its nominal size to a measured size changes the cut sizesPassed
- A tile height below the ceiling leaves no tile above the lineChecked for: stacked; brick 1/2; brick 1/3; herringbone 45; herringbone 90; diagonal.Passed
- Sizes print correctly to 1/16": 7 3/8", 12", 1/2"Passed
- A piece cut at the window is described by the part that remainsPassed
- The part a window removes is never more than the piece itselfPassed
- A niche has five tiled faces, a window return four, a door frame threePassed
- Cut numbers inside an opening run on from one face to the nextPassed
- On brick, the two end cuts match on every coursePassed
- Sliding the layout by one whole tile and joint brings back the same layoutPassed
- Sliding the layout sideways changes the end cuts by the distance slidPassed
- A plain 8'-0" x 8'-0" wall is 64 square feetPassed
- A window or niche comes off the wall's square footagePassed
- Tile to a height: only the tiled part counts, and only the part of an opening below the tile line comes offPassed
- A floor's square footage leaves out its blocks, but not a cabinet with tile all the way under itPassed
- The example master bath floor comes to about 143 square feet of tile, against 170 for its bare rectanglePassed
- The patterns offered are Stacked, Brick, Herringbone and DiagonalPassed
- A square tile is not offered herringbonePassed
- Each pattern shows only its own optionsPassed
- Stacked vertical lays the tile upright, long side up the wallPassed
- Brick horizontal shifts each course along by 50% or 33% of a tilePassed
- Brick vertical stands the tile upright and shifts each column up by 50% or 33% of a tilePassed
- Brick vertical works for a square tile: the stagger runs up the wallPassed
- Herringbone can be laid at 45 degrees or at 90 degreesPassed
- Herringbone 90 degrees lays every tile square to the wall, some across and some upPassed
- The cut list has every cut exactly oncePassed
- The cut list for the 8'-0" brick wall groups 53 cuts into four sizesPassed
- The cut list runs in the order the wall is set: lowest cut firstPassed
- The cut list names the type of each cutPassed
- Cut numbers are written short: runs become rangesPassed
- Every tile, pattern and layout rule lays out with sound numbersChecked for: 8'-0" x 8'-0" wall; 10'-2 1/2" x 9'-0" wall; 4" x 3'-6" pony wall face wall; 3'-1 1/16" x 5'-1 15/16" wall.Passed
- Tile plus grout accounts for the whole wall, for every tile, pattern and layout ruleChecked for: 8'-0" x 8'-0" wall; 10'-2 1/2" x 9'-0" wall; 4" x 3'-6" pony wall face wall; 3'-1 1/16" x 5'-1 15/16" wall.Passed
- A 40'-0" x 40'-0" wall, the biggest allowed, lays out in every patternPassed
- Sliding by hand, by any amount, still leaves a whole wall with sound numbersPassed
- A link reopens the same wall for every tile, pattern, joint and layout rule the editor offersPassed
- Kali's wallChecked for: a 12" niche a quarter inch off the course is moved onto it, and the slivers go; on a 6'-2 1/4" wall in 12 x 24, a tile on the center line leaves 7/8" slivers and a joint leaves 12 15/16" cuts.Passed
- Fitted up and down, no tile above or below the niche is cut by itPassed
- On stacked tile the niche is fitted both ways and replaces whole tiles: nothing at it is cutPassed
- On brick, the niche is fitted to the joints of its own bottom course; the course above meets it with the pattern's own part tilesPassed
- Vertical brick is fitted both ways, to the joints of the niche's left column; herringbone and diagonal are not fitted at allPassed
- A fitted niche stays inside the wall and follows a layout slid by handPassed
- A wall centered on the niche keeps the niche where it is side to sidePassed
- Dragging a niche near a course line snaps it onto the line; its size never changesPassed
- Away from any tile line, a dragged opening is left exactly where it is putPassed
- Snapping pulls the nearer edge: the bottom of the opening onto a course, or its topPassed
- On stacked tile a dragged opening snaps side to side as well; on herringbone it never snapsPassed
- A snapped opening stays inside the wall, and a door only snaps side to sidePassed
- Centered on the doorway is the default for a floorPassed
- Centered on the doorway: the tile either side of the doorway's center line matchesPassed
- Centered on the doorway moves the layout with the doorway, along its wall onlyPassed
- Centered on the room: the cuts at opposite walls match, both waysPassed
- Full tile against a wall: a whole tile sits tight to that wall, and the other way stays centered on the roomPassed
- Floor cuts are numbered from the row farthest from the doorway, working back to the doorPassed
- Along a row, the numbers start at the end farther from the doorway and run straight to the other endPassed
- Every pattern covers a floor: herringbone both ways and diagonal includedPassed
- A doorway is kept inside its wallPassed
- The floor's layout rule is put into wordsPassed
- A floor in a link: the default floor needs nothing, and a link reopens exactly the floor it was copied fromPassed
- A floor's names in a link all start with f_, so they sit beside the walls' own and neither reads the other'sPassed
- Anything wrong in a floor link falls back to the default, and the doorway is kept inside the floorPassed
- Blocks: no whole tile is laid under a cabinet or a wall, and the tile is cut round each onePassed
- Blocks take tile off the floor: the master bath has less tile than its bare rectangle, by about the blocks' areaPassed
- A floor's blocks travel in its link; one that does not fit is pulled inside the floor, and nonsense is droppedPassed
- On a floor the cut list says block, not openingPassed
- Kali's ruleChecked for: a tile the toilet room wall cuts in two is two cuts, each with its own number and size; a 1" piece left to turn the corner is dropped, and the next wall starts with a full tile.Passed
- A sliver on one side of a wall no longer turns the piece on the other side redPassed
- Tile all the way under a cabinet: that cabinet stops cutting the tile, and the others still doPassed
- Tile under a block travels in the linkPassed
- The default wall needs nothing in its linkPassed
- A link reopens exactly the wall it was copied fromPassed
- A link reads in plain wordsPassed
- Anything wrong in a link falls back to the default, so the wall still opensPassed
- A link carries the openings, the tile height and the feature the layout is centered onPassed
- An opening in a link that does not fit its wall is pulled back inside it; one that makes no sense is droppedPassed
- A link carries every wall of a run, each with its own width, openings, rule and slidePassed
- A link with one wall has no other walls; four walls is the most; a gap in the run ends itPassed
- A link carries the wrap switch at each corner and the walls chosen to be centered; a corner is not wrapped unless the link says soPassed
- A link made before the spelling changed from centre to center still opens the same wallPassed
- A link carries a tile or a joint chosen for the center line, on any wall, and drops it where the wall is not centeredPassed
- a wall whose tile starts above the floor keeps that height in the linkPassed
- A thin strip left beside an opening is flagged as a sliverPassed
- Slivers at an opening are counted with the wall's slivers and marked on the cut listPassed
- The sliver limit applies at openings too: a wider limit flags morePassed
- A piece at an opening is named by the shape of its cut: straight, corner, edge or holePassed
- With several openings, no tile is laid inside any of themPassed
- Center on a feature: the cuts either side of the window matchPassed
- Center on a feature moves the layout off the wall's own center, and the rule says soPassed
- A tile height below the ceiling: the layout rule works from the top of the tile, not the ceilingPassed
- An opening is measured from the left of the wall and up from the floorPassed
- A new opening is a usual size and sits inside the wall, even a small wallPassed
- Openings of the same kind are told apart by numberPassed
- Overlapping openings are noticedPassed
- a rectangle traced as four corners has its width times its depth as area, either way roundPassed
- an L-shaped room is the big rectangle less the corner cut out of itPassed
- a side within 2 degrees of level or upright is made exactly level or upright, and a steeper one is left alonePassed
- an outline whose sides cross is recognised, and a plain room is notPassed
- a cabinet traced inside a room is taken off that room's area, and one outside it is notPassed
- in an L-shaped room, a cabinet in the missing corner is not inside the roomPassed
- A typed size is read the way a setter writes itPassed
- A typed size is rounded to the nearest 1/16" and says soPassed
- Nonsense is refused with a plain messagePassed
- A size outside the limits is refused and the limit is namedPassed
- Wall sizes print as feet and inches: 8'-0", 8'-2 1/2", 6"Passed
- A size that is printed can be typed back in and gives the same sizePassed
- Every wall starts centered on itself: with no corner wrapped, each is laid out by its own layout rulePassed
- Wrapped corner: the cut that ends one wall and the cut that starts the next add up to one tile, on every coursePassed
- In a wrapped group the widest wall is centered unless another is chosen; the rest follow itPassed
- Pressing Center on a wall makes it the centered wall of its groupPassed
- With wrap off at a corner, the walls beyond it start fresh on their own layout rulePassed
- Walls are grouped by their wrapped cornersPassed
- Sliding the centered wall carries every wall wrapped to it; a follower's own slide is not usedPassed
- A small piece is dropped on the left of the centered wall too: that wall ends at the corner with a full tilePassed
- On brick the smallest corner piece of any course decides; once it is dropped no course starts with a sliverPassed
- The limit for a corner piece is the sliver limit: a 2" piece is kept, and a wider limit drops itPassed
- Herringbone and diagonal carry round a wrapped corner as one continuous pattern, with nothing droppedPassed
- Herringbone at 45 degrees is centered so the cuts down the left side match the cuts down the rightPassed
- Herringbone at 45 degrees is centered so the cuts along the top match the cuts along the bottomPassed
- Herringbone at 45 degrees looks the same turned half a turn about the middle of the wallPassed
- Starting herringbone with a tile corner on the middle of the wall, as the prototype did, does not match the two sidesPassed
- Herringbone centered Kali's way on the 8'-0" wall in 4 x 16 has no sliversPassed
- Of the two true centers of a herringbone, the one with fewer slivers is keptPassed
- The default layout rule is centered side to side with a full tile at the floorPassed
- Full tile at the ceiling: the top tile sits tight to the ceiling and the cut lands at the floorPassed
- Centered top to bottom: the top and bottom courses are exactly the same heightPassed
- Centered top to bottom keeps whichever of tile-on-center and joint-on-center leaves the bigger cutsPassed
- Full tile at the left: the first tile sits tight to the left sidePassed
- Full tile at the right: the last tile sits tight to the right sidePassed
- On brick, a full tile at the left or right is on the bottom course, and the next course steps overPassed
- The layout rule is put into wordsPassed
- When the layout rule leaves slivers, a rule that leaves fewer is suggestedPassed
- A suggestion changes one direction of the rule when that is enoughPassed
- Nothing is suggested when the rule leaves no slivers, or when no rule does betterPassed
- Herringbone and diagonal get no rule suggestionPassed
- Herringbone is set out the same way whatever layout rule is chosenPassed
- Herringbone at 90 degrees and diagonal start from the middle of the floor linePassed
- Center on a tile puts the middle of a tile on the center line; center on a joint puts a grout joint therePassed
- Either way the two ends still match, and the choice is ignored when the wall is not centeredPassed
- The layout rule says what is on the center line when it was chosen by handPassed
Matches the prototype
The prototype's own engine was run on a fixed set of surfaces and its answers saved. The new engine has to reproduce every piece on every one of them.
- Room as it opens4 surfaces compared, piece by piece.Passed
- Every pattern5 surfaces compared, piece by piece.Passed
- Plain wall5 surfaces compared, piece by piece.Passed
- Layout rules9 surfaces compared, piece by piece.Passed
- Corners12 surfaces compared, piece by piece.Passed
- Tile height9 surfaces compared, piece by piece.Passed
- Measured tile2 surfaces compared, piece by piece.Passed
- Grout joint8 surfaces compared, piece by piece.Passed
- Slid by hand3 surfaces compared, piece by piece.Passed
- Floor5 surfaces compared, piece by piece.Passed
- Inside the openings6 surfaces compared, piece by piece.Passed
- The layout rules give the prototype's start points33 rooms compared.Passed
- Sizes print the way the prototype prints themPassed
- The center rule picks the prototype's start pointPassed
Known gaps
Things the engine does not do yet. Each line says what should happen. They are kept as tests so that none is forgotten, and each turns to Passed when it is built.
- In the prototype's room rules, balance top and bottom makes the two courses exactly equalKnown gap
- The ceiling course is not left as a sliver when full tile at the floor is chosenKnown gap
- Tile height applies inside a niche, window return or door frameKnown gap
- A notched piece on herringbone or diagonal is described by the part that remainsKnown gap
- A wall is shortened at an inside corner by the thickness of the tile on the adjoining wallKnown gap
- The layout rules work for rooms that are not one back wall with a wall on each sideKnown gap